UPS PIco HV4.0B HAT Stack with Battery 450

UPS PIco HV4.0B HAT Stack with Battery 450

SKU: PMS00003
Kategorie: Raspberry Pi
Hersteller: PiModules

The UPS PIco HV4.0B/C HAT Stack with Battery 450 is an advanced Intelligent Mobile Power Bank and Uninterruptible Power Supply for the Raspberry Pi® A+/B+/2/3 and ZERO/W, that adds a wealth of innovative power powering/back-up functionality and development features to the innovative microcomputer!

50,00 €

inkl. 20% USt. , zzgl.

3 Stück im Geschäftslokal lagernd
Versandzeit: 1 - 3 Werktage (AT - Ausland abweichend)

Beschreibung
Bewertungen
Frage zum Artikel

Ordered Item contains:

UPS PIco HV4.0B/C Stack with all described below long list of features
Selected by user battery (default set to LiPO Battery 450 mAh 15C)
Not Soldered2 x Spring Loaded POGO Pins (RUN/PEN)
SMD Soldered Battery Socket (2.5mm)
SMD Soldered FAN Socket (2mm)
40 pin header (not passed through)
Not Soldered2mm compatibility Jumper for Raspberry Pi® 3 Assembly
Mounting Spacers, screws, nuts needed to mount on the Raspberry Pi® microcomputer

NOTE:All not soldered THT parts need to be soldered by user, or by our soldering service available as an option during ordering.

Ordered Item does not contain and could be ordered separately if needed for specific application:

Batteries

Standard/High Capacity Batteries (1500 mAh, 4000 mAh, 8000 mAh)

Li-Ion 18650 Batteries/18650 Battery Holders HAT

PIco Single LP/LF Li-Ion 18650 Battery Holder (without battery)
PIco Double Li-Ion 18650 Battery Holder (without battery)
Li-Ion 18650 2600 mAh Battery

AA NiMH Batteries/AA NiMH Battery Holders HAT

AA NiMH Battery Holder (without battery)
AA NiMH 2000 mAh Battery (3 pcs)

Super Capacitors

100F Super Capacitor (mounted on UPS PIco HV4.0B)
300F Super Capacitor Separate HAT
500F Super Capacitor Separate HAT

Through Hole Add-on Parts

Infrared Receiver
ON/OFF micro Slide Switch
2×10 pins 2mm PIco header
3 pin 2mm RS232 THT socket and header (without cable)
80 dB Sound Electromagnetic Transducer
DPDT 2A RELAY

Application Specific Add-on Extensions

TCXO – Temperature Compensated Ultra Stable Clock Generator (1.5 ppm) for the embedded RTC (if needed a high stability RTC)
3 pin 2mm RS232 socket/header and 100 mm cable (ended with 9 pins D-Sub)
UPS PIco HV4.0 Terminals Blocks Additional PCB (20 I/O are directed to Terminal Block) for easy mounting
PiBlock Case with external Slide Switch, and 2 External user buttons, and slot for Terminals Block PCB

Short System Overview

UPS PIco HV4.0B/C Stack is an Ultimate Powering System HAT that adds a wealth of innovative powerful and development features to the Raspberry Pi® microcomputer! It has been designed especially for the Raspberry Pi® 4, and taking into account all enhanced power and cooling requirement of the Raspberry Pi® 4 models, however in addition it is still compatible with all former Raspberry Pi models. The core functionality of the UPS PIco HV4.0B/C Stack is to protect and automatically shut-down your Raspberry Pi if there is a cable power failure and can be set to automatically monitor and reboot your Pi once cable power has been restored! However, it is only a small part of plenty and powerful functionalities that are implement on this small HAT.

The UPS PIco HV4.0B/C Stack is the only one on the market that offers such enhanced set of features at once:

General

HAT Dimensions Compliant
Email broadcasting on events (Cable Power loss/return, Wake-up, User Button, A/D etc)
Plug and Play
Ultra light System.d Daemon based on threading
GPIO free (all GPIOs are available for user application) interaction with Raspberry Pi® via I²C
Enhanced System Monitoring and Programming API
Labeled J8 Raspberry Pi® GPIO Pins for Easy Plug & Play of experimental cables
Standard THT 40 Pin connector (not soldered)
Remote bootloader for Live Firmware Update on remote locations
Local bootloader for Live Firmware Update

Powering Options

2 independent power back-up sources: Battery and Super Capacitor automatically switching between them according to powering condition, used together or separately.
Enhanced Line Interactive UPS functionality (25us response time)
Additional File Safe Shutdown and Start-up Functionality on a Single Button
Continuously 3.2A@5.25V supply on battery power backup
Programmable Battery backed-up of independent power sources of 200@5V and 3V3
Intelligent Mobile Power Bank functionality with save shutdown/start-up, with Internal or External Slide Switch and RTC

Supported Batteries Types, Super Capacitors and Capacities

Supports a wide range of different Chemistry batteries and Super Capacitors (LiPO/LiFePO4/Li-Ion/NiMH/SAL/Super Capacitor)
Support for Li-Ion 18650 low cost batteries (from Electronic Cigarettes) with dedicated mounting base PCB HAT screwed on top
Support for LiPO 18650 batteries with dedicated mounting base PCB HAT screwed on top
Support for LiFePO4 18650 batteries with dedicated mounting base PCB HAT screwed on top
Support for Super Capacitor 100F soldered to PCB
Support for Super Capacitor 300F as a separate PCB HAT screwed on top
Support for Super Capacitor 500F as a separate PCB HAT screwed on top
Both Back-up Power Sources (Battery and Super Capacitor) can be used at once (with automatic selection and switching) or one of them, thanks to ultra low voltage High Current Boost Converter

Embedded Peripherals and Interfaces

2 User Programmable buttons
2 User Programmable LEDs (with mapping capability of the system behavior LEDs)
System File Safe Shutdown/Start-up button with additional cable connectivity to external button
2 x 200 ks/s ESD protected A/D with voltage follower (high impedance)
ESD Protected 3V3/5V0 1-wire interface
Infra-Red Receiver Sensor Interface (IR Not Included) directly connected to the GPIO18
Integrated Hardware Real Time Clock (RTC) with Battery Back-Up
Optionally TCXO with Ultra Stable RTC (1.5 – 5 ppm @+25°C) – Error Over Time ±0.432sec/day; ±12.960sec/month; ±2.628min/year
DPDT 2A RELAY on the same PCB
Programmable Integrated PWM Sounder (programmable by user API or Automatic), able to play music
Programmable embedded quad +/-12V RS232 interface (2 at once time).
Programmable Integrated PWM FAN (integrated within the basic order) running based on Raspberry Pi Core temperature

Embedded Sensors

Single High-side bi-directional hardware current sensing monitor with power calculation
onboard temperature sensor
Battery Level Voltage
Super Capacitor Voltage
Raspberry Pi GPIO 5V level

User/Programmer Interface

I²C PIco API Interface for Control and Monitoring, with over 50 programming registers
Support for 4 different users selectable I2C addresses sets:
- DEFAULT: 0x68, 0x69, 0x6A, 0x6B, 0x6C, 0x6D, 0x6E, 0x6F
- NO_RTC: 0x69, 0x6
- ALTERNATE1: 0x58, 0x59, 0x5A, 0x5B, 0x5C, 0x5D, 0x5E, 0x5F
- ALTERNATE2: 0x48, 0x49, 0x4A, 0x4B, 0x4C, 0x4D, 0x4E, 0x4F

RTC Support and System Scheduler

RTC Scheduler
Enhanced shutdown and start-up system based on various internal/external events events: Time stamp, A/D level, RS232 data, Cable Powering/Loss (UPS), Battery Level, I/O Level, etc

Case Compatibility

No Additional External Power Input Required. System is monitoring power status over 5V GPIOs, therefore is compatible with 99% of all existing cases
Fits Inside Most Existing Cases as no extra cabling is needed

System Monitoring

Status Monitoring – Powering Mode, Inbound current, Outbound current, Powering Voltage, Battery Voltage, Super Capacitor Voltage, Temperature (Raspberry Pi Core and UPS PIco), Timer State
Events Pi Log feature
System LEDs – SYS, BAT, CHG, INF, FAN, SCA, TMR, TMP (optionally selected can be mapped to User LEDs)
System Healthy, that informs user remotely if Raspberry Pi and UPS Pico HV4.0B are running properly and system is power protected (based on various internal system triggers)

User Applications Security

(optional) 2-way XTEA Based Encryption Engine for User Intellectual Properties protection

System Protection

Direct Raspberry Pi® Hardware Reset Button via Spring Loaded Pogo Pin point to RUN
Direct Raspberry Pi® Hardware ON/OFF via Spring Loaded Pogo Pin point to PE, Even if Powering Cable is entered to Raspberry Pi®
Programmable Watch-Dog Hardware feature (Still Alive Timer)
PPTC 3A@5V fuse
ZVD circuit on all 5V GPIO connections
Micro-controllerbased watch-dog
Over Temperature protection
Over Current protection

System Design

Designed and Simulated with PDA Analyzer with one of the most advanced CAD/CAM Tools – Altium Designer
Design Based on Microchip 16-bit 16 MIPS micro controller
Industrial Originated

PCB Construction

2 oz copper PCB manufactured for proper high current supply and cooling
6 mils track/6 mils gap technology 6 layers PCB
PCB Surface Finishing – Immersion Gold
Multi-layer Copper Thermal Pipes for increased System Thermal Response and better passive cooling

Documents

Es gibt noch keine Bewertungen.

Kontaktdaten

E-Mail

Frage zum Artikel

Ihre Frage

Montag	10:00 - 18:30
Dienstag	13:00 - 18:00
Mittwoch	10:00 - 18:00
Donnerstag	13:00 - 18:00
Freitag	10:00 - 18:00
Samstag	10:00 - 12:00
Sonntag	Geschlossen